IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready I’ve ran the following commands on the Kali ifconfig I’ve tried the method above several times on different ports also with no success. Also I’ve noticed that the usb icon at the bottom right of the screen is showing no activity i.e red or green blinking dots and it states ‘No USB Devices Attached’. I’ve tried your steps above however with no success. A lot of the times the adapter just cuts off when I start Kali and when I boot up Kali and then connect the adapter it dosent switch on as it should. I works fine on the host machine however it isn’t passing through to kali linux. The issue i have is when I try using the the alpha AWUS036NHA wireless adapter. I’m new to penetration testing and have recently been taking online course, however I installed Kali Linux on windows 10 recently which all went fine. Surprisingly, it was working last week and when i set it up that time, it was nothing extra i needed to do. I installed, removed and reinstalled the drivers but still no success. Usbcore 249856 5 usbhid,ehci_hcd,ohci_pci,ohci_hcd,ehci_pci Scsi_mod 225280 4 sd_mod,libata,sr_mod,sgĬryptd 24576 3 ablk_helper,ghash_clmulni_intel,aesni_intel Libata 249856 4 ahci,ata_piix,libahci,ata_generic Nfnetlink 16384 2 nfnetlink_log,nfnetlink_queue TX errors 0 dropped 0 overruns 0 carrier 0 collisions iwconfigīus 001 Device 003: ID 80ee:0021 VirtualBox USB Tabletīus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root lsmod TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 The Kali is in Virtualbox (latest), hosted on Windows 10. I followed the steps you mentioned but not able to get the Alpha adapter detected and work in Kali Linux. Unfortunately, no low hanging fruit there either.Īll in all, an easy to set up and use device that I’m looking forward to playing with for some wireless testing. Wash v1.5.2 WiFi Protected Setup Scan ToolĬopyright (c) 2011, Tactical Network Solutions, Craig HeffnerīSSID Channel RSSI WPS Version WPS Locked ESSID Once I put the device properly in monitor mode, then I ran airodump! ~# airodump-ng wlan0monĪfter letting this run for a while, I had a fair amount of SSIDs and beacons detected! Unfortunately, nothing in my immediate vicinity was running WEP.įinally, I ran Wash to find out if there were any weak WPS devices that I could use to test out my new card. I verified the monitor mode device by running ifconfig and viewing the output. (mac80211 station mode vif disabled for wlan0) (mac80211 monitor mode vif enabled for wlan0 on wlan0mon) Phy0 wlan0 ath9k_htc Atheros Communications, Inc. If airodump-ng, aireplay-ng or airtun-ng stops working afterĪ short period of time, you may want to run 'airmon-ng check kill' ~# airmon-ng start wlan0įound 3 processes that could cause trouble. To do this, I started airmon-ng on the wlan0 device. With everything properly connected and configured, it was time to set up monitor mode. To verify the connection, I again ran iwconfig and had a wlan0 device this time. I then connected my device to my workstation, VirtualBox detected it, and then automatically passed on to the VM. As you can see, there are no wireless devices connected to my VM yet. Once I created a new blank filter, I just added the appropriate Vendor ID and Product ID and saved it.Īfter I had the device filter setup, I detached the device from my workstation and logged into Kali. That said, I ran into some issues with the default filter, so I had to create a blank filter with the proper values. Once I got the device out of the box, I hooked it up to my workstation.Īfter I connected the card, VirtualBox detected it for USB pass-thru.įirst, I wanted to set up a device filter so that it would automatically be connected to my VM. To start, the Alfa AWUS036NHA I ordered came with a 9dBi antenna, which was awesome. Please note that links listed may be affiliate links and provide me with a small percentage/kickback should you use them to purchase any of the items listed or recommended.I recently picked up a new Alfa AWUS036NHA to play with for wireless testing, scanning, and general signal boosting. Kali Linux Alfa adapters fix AWUS036ACH: 0:00 Fix Kali Linux drivers for Alfa AWUS036NHA, Alfa AWUS036ACM and Alfa AWUS036ACH adapters (and others).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |